Gilderflukeco old MACs 8 bit Digital Audio System Manual do Utilizador Página 54
- Página / 110
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Configuration via Dip Switches:
If you don't have a terminal or computer handy to do the configuration for a digital audio Repeater,
you can use the two dip switches located on each card. If at all possible, we recommend you use the
serial port configuration mode if at all possible.
To configure any of the features on the card, set dip switch 1 as shown and then enter in dip switch
2 as desired. To record this condition, turn switch 1 on dip switch one on, and then off. Your selection
will have been recorded and you can then change the dip switches to set up the next selection.
In the notation used in the following selection, a 0 = a dip switch position in the 'off' position, while a
1 = a dip switch in an 'on' condition. Bit position 7 is controlled by dip switch position 1. Bit 0 is controlled
by dip switch position 8
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
TO SELECT TRACK NUMBER:
DIPSW1= 00000000
DIPSW2= TRACK NUMBER
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
TO SELECT 'A' INPUT ACTION ON CLOSING:
DIPSW1 = 00000001
DIPSW2 =
SWITCH 1 = STOP REPEATER AT END OF SPIEL ON THIS EDGE
SWITCH 2 = START REPEATER LOOPING ON THIS EDGE
SWITCH 3 = START REPEATER ON THIS EDGE
SWITCH 4 = RESET REPEATER TO BEGINNING ON THIS EDGE
SWITCH 5 = STOP REPEATER ON THIS EDGE
SWITCH 6 = UN-MUTE AUDIO ON THIS EDGE
SWITCH 7 = FULL MUTE AUDIO ON THIS EDGE
SWITCH 8 = HALF MUTE AUDIO ON THIS EDGE
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
TO SELECT 'A' INPUT ACTION ON OPENING:
DIPSW1 = 00000010
DIPSW2 =
SWITCH 1 = STOP REPEATER AT END OF SPIEL ON THIS EDGE
SWITCH 2 = START REPEATER LOOPING ON THIS EDGE
SWITCH 3 = START REPEATER ON THIS EDGE
SWITCH 4 = RESET REPEATER TO BEGINNING ON THIS EDGE
SWITCH 5 = STOP REPEATER ON THIS EDGE
SWITCH 6 = UN-MUTE AUDIO ON THIS EDGE
SWITCH 7 = FULL MUTE AUDIO ON THIS EDGE
SWITCH 8 = HALF MUTE AUDIO ON THIS EDGE
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
TO SELECT 'B' INPUT ACTION ON CLOSING:
DIPSW1 = 00000011
DIPSW2 =
SWITCH 1 = STOP REPEATER AT END OF SPIEL ON THIS EDGE
SWITCH 2 = START REPEATER LOOPING ON THIS EDGE
SWITCH 3 = START REPEATER ON THIS EDGE
SWITCH 4 = RESET REPEATER TO BEGINNING ON THIS EDGE
SWITCH 5 = STOP REPEATER ON THIS EDGE
SWITCH 6 = UN-MUTE AUDIO ON THIS EDGE
SWITCH 7 = FULL MUTE AUDIO ON THIS EDGE
SWITCH 8 = HALF MUTE AUDIO ON THIS EDGE
GILDERFLUKE & C
o
. ¥ 205 SOUTH FLOWER ST. ¥ BURBANK, CALIF. 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485
44
- - MACs 1
- - DIGITAL AUDIO SYSTEM 1
- This page left blank 2
- This page left mostly blank 10
- GILDERFLUKE & C 10
- - MACs DIGITAL AUDIO SYSTEM 11
- - A System Overview 11
- Approximate Play Times: 13
- Audio Processing: 15
- REPEATER 21
- GLOBAL/MIX BUS #1 23
- GLOBAL/MIX BUS #2 23
- GLOBAL/MIX BUS #3 23
- GLOBAL/MIX BUS #4 23
- AUXILIARY INPUT 23
- Actual Playing Times: 25
- (7,031 Hz UPDATE RATE) 26
- (8,789 Hz UPDATE RATE) 26
- (11,718 Hz UPDATE RATE) 27
- (17,578 Hz UPDATE RATE) 27
- (23,437 Hz UPDATE RATE) 28
- (35,156 Hz UPDATE RATE) 28
- - Low Level Mixer 30
- - Global/Mix Buss 30
- - Shelving Equalizer 37
- CC-1600 or CC-400: 38
- Volume and Other Adjustments: 40
- 18IVCA BUS 42
- - Aux. Port Usage 43
- "m" (5AA5) (TRACK#) 45
- "b" Baud Rate: 46
- - Summary of Setup Commands 53
- - Serial Port Commands 60
- TWO STOP BITS 62
- ONE START BIT 62
- SEVEN DATA BITS 62
- ODD PARITY BIT 62
- TRACK 00 Setup Mode Selected 63
- 3800000001290000000000 65
- 00000000 66
- Start Commands 69
- Stop At End Commands: 72
- Select Spiel Commands: 72
- - MX-100 / MX-200 85
- - Memory Expansion Boards 85
- - MA-100 PA Master 88
- - MA-200 PA Interface 88
- - Public Address Stations 88
- - DAS-100 91
- - Digital Audio Sampler 91
- - Hardware Requirements 92
- - Installation 93
- - Software and Operation 94
- - Internal Details 95
- - Left Window Display 96
- - Main Menu Commands 97
- ILDERFLUKE & C 100
- - Evaluation Menu Commands 102
- - Data Dump Commands 103
- - EPROM Image Menu Commands 104
- - Report Menu Commands 105
- - Calibration 106
- - A Sample Sample Session 107
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais